Chef CHG642SA Manuel d'utilisateur Page 13
- Page / 20
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
installation LPG conversion -
DONG YANG regulator
Checking the gas supply
1. Check the manometer zero point is correct.
2. Connect the manometer to the cooktop pressure point. This
is located on the regulator.
3. Turn on the gas supply and electricity and try to ignite
the gas.
TIPS & INFORMATION
tips & information
It will take additional time to light the gas for the first time as
air needs to be purged from the pipes.
4. With the appliance operating check the outlet pressure:
• when all burners of the appliance are operating
at maximum,
• when the smallest burner of the appliance
is operating at minimum.
Under these conditions the outlet pressure should not vary
from the nominal outlet pressure of 1.00kPa by more than
+/–0.20kPa.
If the regulator appears to not be performing satisfactorily,
then check the following points.
1. If the outlet pressure is consistently too low then the inlet
pressure may be too low and adjustment of an upstream
regulator may be needed, or an upstream regulator or
valve with insufficient flow capacity may be present in the
gas supply line. If this is suspected then it may be necessary
to repeat the checks whilst
measuring both the inlet and outlet pressure to determine
if the inlet pressure is in the range 1.13 – 5kPa.
2. Check that the regulator has been fitted to the gas supply
line in the correct orientation, the arrow on the base of the
body indicates the direction of gas flow.
Once these checks have been completed, if the regulator
still fails to perform in a satisfactory manner it should be
replaced.
TIPS & INFORMATION
tips & information
Refer to page 15 if you have been supplied with a
CHANT regulator.
This appliance is fitted with Natural Gas burner injectors.
Please follow the procedure below if a conversion to suit LP
gas is required.
The conversion kit contains appropriate LPG
injectors and 1 LPG sticker.
To convert to LPG
1. Remove the hotplate burners to access the hotplate
injectors. Replace the factory fitted NG injectors with the
appropriate injectors, as supplied (see Table 3).
2. Unscrew the hex nut from the regulator. The hex nut, brass
washer and nylon insert will disengage as
an assembly.
3. Unclip the nylon insert from the nut assembly by rotating the
insert ¼ turn, and pulling it free.
4. Turn over the insert, and clip back into position.
5. Refit the hex nut assembly to the regulator ensuring that it is fully
screwed down. The regulator is now set for connection to LP.
6. Turn on the gas supply and at each new connection check
for leaks using soapy water: each hotplate valve should be
turned on, one at a time, and the injector hole blanked off
for several seconds.
7. The operation of the regulator can be confirmed by
connecting a manometer to the pressure test point located
on the side of the regulator body adjacent to the outlet.
With the appliance operating check the outlet pressure
• when all burners of the appliance are operating
at maximum,
• when the smallest burner of the appliance is operating at
minimum.
Under these conditions the outlet pressure should not vary
from the nominal outlet pressure of 2.60kPa by more than
+/–0.52kPa.
8. If the regulator appears to not be performing satisfactorily
then check the following points.
• If the outlet pressure is consistently too low then the inlet
pressure may be too low and adjustment of an upstream
regulator may be needed, or an upstream regulator or
valve with insufficient flow capacity may be present in
the gas supply line. If this is suspected then it may be
necessary to repeat the checks whilst measuring both the
inlet and outlet pressure to determine if the inlet pressure
is in the range 2.75–7.00kPa.
• Check that the insert has been fitted correctly as per
diagram figure 7. Check that the hex nut is fully
screwed down.
Gas Cooktops LP CONVERSION - DONG YANG 13
- GAS COOKTOPS 1
- User and Installation Manual 1
- ENVIRONMENTAL TIPS 2
- DONG YANG regulator 13
- LPG conversion 14
- CHANT regulator 15
- Diagram 1 16
- Figure 9 16
- Figure 10 17
- Figure 11 17
- 18 NOTES Gas Cooktops 18
- Warranty 19
- ABN 51 004 762 341 20
Produits connexes et manuels pour Plaques chauffantes Chef CHG642SA
(16 pages)Philips HD2696/90 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Toaster Philips HD2696/90.
Wir stellen 5 PDF-Handbücher Philips HD2696/90 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels